Архів інструкцій
Инструкция Архів інструкцій
Архивный PDF-документ для ознакомления.
Инструкция · Русский · Обновлено: 12 августа 2026 г.
Оригинальный PDF
Завантаження PDF…
Оставить заявку мастеру
Нужна диагностика или помощь с инструкцией? Передайте мастеру модель котла и код ошибки.
Текст инструкции для поиска
Страница 1
Pag. 1/32 Accessorio per la gestione di un impianto misto Modello PARTAGE HT Abbinabile alle caldaie modello LUNA HT… NUVOLA HT 330 IT Controller for twin circuit installations PARTAGE HT model To match with gas boilers model LUNA HT… NUVOLA HT 330 GB Istruzioni per l’INSTALLATORE Installation INSTRUCTIONS IT GB
Страница 1 PDF
Страница 2
Pag. 2/32 INDICE / TABLE OF CONTENTS IT Pag. Descrizione accessorio e realizzazione del circuito idraulico 3 Dimensioni e attacchi idrici 3 Montaggio accessorio AGU 2.500 sul cruscotto comandi della caldaia 4 Schema di collegamento accessorio AGU 2.500 5 Collegamento elettrico accessorio 6 Descrizione led scheda elettronica 8 Impostazione parametri su scheda elettronica 9 Gestione delle differenti zone 9 Collegamento del termostato per impianti a pavimento 13 Prevalenze pompe 13 Descrizione KIT opzionale per il collegamento di una seconda pompa sul circuito alta temperatura 14 Tabella riassuntiva parametri da impostare su scheda di caldaia 15 Caratteristiche tecniche 16 GB Description of the controller and its water circuits 17 Dimensions and hydraulic connections 17 Assembly of AGU 2.500 accessory in the boiler’s control panel 18 Accessory AGU 2.500 electric wiring diagram 19 Fulfilment of the electric connection 19 Controller electric wiring diagram 20 LEDs descriptions of electronic control card 22 Setting the PCB parameters 23 Management of different zones 23 Pump head values 23 Floor thermostat connecting (low temperature floor circuit) 27 Optional second pump kit for the high temperature circuit 28 Setting parameters on main boiler PCB 29 Technical specifications 30 Baxi S.p.A. dichiara che questo apparecchio è dotato di marcatura CE conformemente ai requisiti essenziali delle seguenti Direttive: - Direttiva Bassa Tensione 73/23/CEE - Direttiva Compatibilità Elettromagnetica 89/336/CEE This BAXI appliance bears the CE mark in compliance with the basic requirements as laid down in the following Directives: - Low Voltage Directive 73/23/CEE - Electromagnetic Compatibility Directive 89/336/CEE GB IT
Страница 2 PDF
Страница 3
Pag. 3/32 1. Descrizione accessorio e realizzazione del circuito idraulico Mediante questo accessorio, provvisto di collettore aperto, è possibile effettuare la gestione contemporanea di un impianto misto costituito da una zona ad alta temperatura (≤ 80°C) ed una zona a bassa temperatura (≤ 45°C). Le dimensioni ridotte del telaio (160 mm di profondità) permettono una facile installazione a scomparsa oltre ad un’installazione pensile. L’accessorio è provvisto di una pompa di circolazione, a servizio della zona ad alta temperatura, comandata da un termostato ambiente di zona. La zona a bassa temperatura è costituita da una valvola miscelatrice ed una pompa di zona. Questa pompa può essere comandata mediante un termostato ambiente, un regolatore climatico SIEMENS QAA73 oppure attraverso una regolazione climatica con sonda esterna (senza TA e senza QAA73). 2. dimensioni e attacchi idrici Figura 1 Figura 2 Legenda : M G3/4” F: mandata caldaia R G3/4”M: ritorno caldaia Mat G3/4”F: mandata impianto alta temperatura ≤ 85°C Rat G3/4” F: ritorno impianto alta temperatura Mbt G1” M: mandata impianto bassa temperatura ≤ 45°C Rbt G1” F: ritorno impianto bassa temperatura IT
Страница 3 PDF
Страница 4
Pag. 4/32 3. Montaggio accessorio AGU 2.500 sul cruscotto comandi della caldaia Dopo aver tolto il coperchio del cruscotto comandi montare la piastra (B) fornita con l’accessorio, quindi montare l’accessorio stesso (C). Nota: per agevolare il collegamento tra l’accessorio e la scheda elettronica, collegare il cablaggio (A) alla scheda prima del fissaggio della piastra (B). Per consentire il montaggio del coperchio del cruscotto comandi risulta necessario tagliare i due piolini in plastica presenti sul coperchio stesso in corrispondenza dell’accessorio AGU 2500. L’AGU 2.500 è fornito insieme a questo accessorio . Figura 3
Страница 4 PDF
Страница 5
Pag. 5/32 4. Schema di collegamento accessorio AGU 2.500 Tabella collegamenti accessorio AGU 2.500 Morsetti AGU 2.500 Morsetti scheda elettronica Descrizione 1-2 X 51 1-2 X 101 Sonda NTC 1(L)2(N) X 52 1(L)2(N) X 203 Alimentazione elettrica AGU 2.500 3(L)4(N) X 52 1(L)2(N) X 201 Alimentazione pompa (zona bassa temperatura) 5(chiude)6(N)7(apre) X 52 5(L)4(N)3(L) X 201 Comando valvola mix (apertura-chiusura) Tabella collegamenti morsettiera M2 di caldaia Z Morsettiera M2 Morsetti scheda elettronica Descrizione 3-4 1-2 X 11 Termostato ambiente (TA) di caldaia 5-6 3-4 X 101 Termostato sicurezza (TP) di caldaia Figura 4 Scheda elettronica accessorio impianto misto Scheda elettronica LMU54 (connettore X-40)
Страница 5 PDF
Страница 6
Pag. 6/32 5. Collegamento elettrico accessorio L’accessorio deve essere collegato elettricamente ad una rete d’alimentazione 230 V monofase + terra mediante il cavo a tre fili in dotazione. L’allacciamento deve essere effettuato tramite un interruttore bipolare con apertura dei contatti di almeno 3 mm. In caso di sostituzione del cavo d’alimentazione, deve essere utilizzato un cavo armonizzato “HAR H05 VV-F” 3x0,75 mm2 con diametro massimo di 8 mm. Nota: è possibile togliere l’alimentazione elettrica su quest’accessorio premendo l’interruttore visibile frontalmente (luce interruttore spenta = off - - figura 5). Figura 5 Tasto ON/OFF
Страница 6 PDF
Страница 7
Pag. 7/32 COLORI CAVI : B bianco C celeste R rosso M marrone N nero G/V giallo / verde BL blu Figura 6 Collegamento connettori: X1 Alimentazione elettrica (2 Fase; 1 Neutro). FA1 Collegamento di terra. X3 Alimentazione pompe. 1 Fase pompa zona bassa temperatura. 2 Neutro pompa zona bassa temperatura. 3 Fase pompa zona alta temperatura. 4 Neutro pompa zona alta temperatura. 5 (N) - 6 (F) Predisposizione collegamento seconda pompa su circuito alta temperatura. X3B Alimentazione valvola miscelatrice. 1 Fase apertura valvola. 2 Neutro valvola. 3 Fase chiusura valvola. 4 Non utilizzato. X4 Ingresso sonda NTC/Termostato a pavimento. 1-2 Sonda NTC circuito miscelato. 3-4 Non utilizzati 5-6 Termostato a pavimento 50°C (clicson). X7 Ingresso termostati ambiente. 1-2 Predisposizione TA 2a zona alta temperatura (TA3). 3-4 TA zona alta temperatura (TA2). 5-6 Non utilizzati
Страница 7 PDF
Страница 8
Pag. 8/32 6. Descrizione led scheda elettronica Figura 7 LED Acceso: valvola in chiusura LED Acceso: valvola in apertura LED Acceso: scheda in tensione 230 V~ LED Acceso: pompa 2 in funzione (zona TA3 – fig.6) LED Acceso: pompa 1 in funzione (zona TA2 – fig.6)
Страница 8 PDF
Страница 9
Pag. 9/32 7. Impostazione parametri su scheda elettronica 1 - tenere premuti contemporaneamente i tasti ▲▼ , presenti sul pannello frontale della caldaia, fino alla comparsa sul display del parametro “H90”; 2 - premere il tasto ▲ per selezionare i parametri in ordine crescente; premere il tasto ▼ per selezionare i parametri in ordine decrescente. Per modificare il parametro visualizzato premere i tasti +/-. Il dato è automaticamente memorizzato quando viene selezionato un nuovo parametro; 3 - premere il tasto per memorizzare ed uscire dal livello di programmazione. Per la descrizione dei parametri fare riferimento alla “tabella riassuntiva parametri da impostare su scheda di caldaia” (paragrafo 12). 8. Gestione delle differenti zone 8.1 CON SONDA ESTERNA Collegare la sonda esterna ai morsetti 7–8 della morsettiera M2 (figura 4), come descritto nel manuale istruzioni della caldaia. 8.1.1 Regolazione climatica (senza TA e QAA73) Assicurarsi che ci sia il ponticello tra i contatti 1-2 e 3-4 della morsettiera M2 di caldaia (figura 4). 8.1.2 Utilizzo di termostati ambiente (TA) zona alta temperatura: Il contatto del termostato ambiente della zona alta temperatura (TA2), deve essere collegato ai morsetti 3-4 della morsettiera X7 della scheda elettronica dell’accessorio (figura 6). La programmazione giornaliera deve essere effettuata direttamente sul pannello comandi della caldaia. La scelta della curva climatica “kt”, relativa alla parte d’impianto ad alta temperatura, deve essere effettuata impostando il parametro 532 della scheda elettronica. Vedere il grafico 1, riportato nel manuale istruzioni della caldaia, per la scelta della curva riferita ad una temperatura ambiente di 20°C. E’ possibile effettuare la traslazione della curva scelta premendo il pulsante , presente sul pannello comandi della caldaia, e modificando il valore visualizzato premendo i tasti +/-. Aumentare il valore visualizzato in caso non si raggiunga la temperatura ambiente desiderata all’interno del locale da riscaldare.
Страница 9 PDF
Страница 10
Pag. 10/32 zona bassa temperatura: Il contatto del termostato ambiente della zona a bassa temperatura deve essere collegato ai morsetti 1-2 della morsettiera M2 di caldaia (figura 8). La scelta della temperatura di riscaldamento massima deve essere effettuata impostando il parametro 507 della scheda elettronica. Il parametro 615 deve essere “0”. Il parametro 552 deve essere “51” per le caldaie monotermiche, o equipaggiate di bollitore, e “54” per le caldaie bitermiche istantanee. La scelta della curva climatica “kt” deve essere effettuata impostando il parametro 533. Vedere il grafico 1, riportato nel manuale istruzioni della caldaia, per la scelta della curva riferita ad una temperatura ambiente di 20°C. E’ possibile effettuare la traslazione della curva scelta impostando il parametro 535. 8.1.3 Utilizzo di termostato ambiente e regolatore climatico QAA73 Zona ad alta temperatura: vedere punto 8.1.2 zona bassa temperatura Il regolatore climatico QAA73 deve essere connesso ai morsetti 1-2 della morsettiera M2 di caldaia (figura 9). La scelta della temperatura di riscaldamento massima deve essere effettuata impostando il parametro 507 della scheda elettronica. Il parametro 615 deve essere “0”. Il parametro 552 deve essere “51” per le caldaie monotermiche, o equipaggiate di bollitore, e “54” per le caldaie bitermiche istantanee. IMPORTANTE: è necessario che il parametro 80 “pendenza HC2”, impostabile sul regolatore climatico QAA73, sia --.- non attivo (vedere capitolo 15.2 del manuale istruzioni della caldaia). La scelta della curva climatica “kt” deve essere effettuata impostando il parametro 70 “pendenza HC1” del regolatore climatico QAA73 come descritto al capitolo 15.2 del manuale istruzioni della caldaia. Vedere il grafico 3, riportato nel manuale istruzioni della caldaia, per la scelta della curva riferita ad una temperatura ambiente di 20°C. La traslazione della curva avviene in modo automatico in funzione della temperatura ambiente impostata mediante il regolatore climatico QAA73.
Страница 10 PDF
Страница 11
Pag. 11/32 8.2 SENZA SONDA ESTERNA 8.2.1 Utilizzo di termostati ambiente (TA) Zona ad alta temperatura: Il contatto del termostato ambiente della zona alta temperatura (TA2), deve essere collegato ai morsetti 3-4 della morsettiera X7 della scheda elettronica dell’accessorio (figura 6). La scelta della temperatura di riscaldamento e l’eventuale programmazione giornaliera deve essere effettuata direttamente sul pannello comandi della caldaia. Zona bassa temperatura: Il contatto del termostato ambiente deve essere connesso ai morsetti 1-2 della morsettiera M2 di caldaia (figura 8). La scelta della temperatura di riscaldamento massima deve essere effettuata impostando il parametro 507 della scheda elettronica. Il parametro 615 deve essere “0”. Il parametro 552 deve essere “51” per le caldaie monotermiche, o equipaggiate di bollitore, e “54” per le caldaie bitermiche istantanee. 8.2.2 Utilizzo di termostato ambiente e regolatore climatico QAA73 zona ad alta temperatura: vedere punto 8.2.1 zona bassa temperatura: Il regolatore climatico QAA73 deve essere connesso ai morsetti 1-2 della morsettiera M2 di caldaia (figura 9). La scelta della temperatura di riscaldamento massima deve essere effettuata impostando il parametro 507. IMPORTANTE: è necessario che il parametro 80 “pendenza HC2”, impostabile sul regolatore climatico QAA73, sia --.- non attivo (vedere capitolo 15.2 del manuale istruzioni della caldaia).
Страница 11 PDF
Страница 12
Pag. 12/32 Schemi di collegamento termostati ambiente (TA) e regolatore climatico QAA73 su morsettiera M2 di caldaia Figura 9 Figura 8 M2 M2
Страница 12 PDF
Страница 13
Pag. 13/32 9. Collegamento del termostato per impianto a pavimento Il sistema è provvisto d’un termostato di sicurezza di 50°C per impianti a bassa temperatura. Nel caso si rende necessario l’utilizzo d’un termostato differente, può essere utilizzato un termostato a collare, reperibile in commercio, che deve essere collegato ai morsetti 5-6 della morsettiera M2 di caldaia in sostituzione a quello esistente (figura 4). 10. Prevalenze pompe 10.1. Pompa circuito bassa temperatura 0 1 2 3 4 5 6 7 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 Portata acqua l/h Prevalenza mH2O 10.2. Pompa circuito alta temperatura 0 1 2 3 4 5 6 7 8 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 Portata acqua l/h Prevalenza mH2O III II III II
Страница 13 PDF
Страница 14
Pag. 14/32 11. Descrizione KIT opzionale per il collegamento di una seconda pompa sul circuito alta temperatura L’accessorio è predisposto per il collegamento di una pompa supplementare per gestire una seconda zona in alta temperatura. Il kit è costituito da: - n°1 pompa GRUNDFOS modello UPS 15/60 230 V-50 Hz; - n°3 tubi (A,B,C figura 10); - n°1 VALVOLA DI RITEGNO G ¾ FF (figura 10); - n°1 cablaggio elettrico. La pompa supplementare deve essere collegata ai morsetti 5-6 del connettore X3 (figura 6). Il termostato ambiente di questo circuito deve essere collegato ai morsetti 1-2 (TA3) del connettore X7 (figura 6). B Figura 10 POMPA UPS 15/60 VALVOLA DI RITEGNO G ¾ FF. A C
Страница 14 PDF
Страница 15
Pag. 15/32 12. Tabella riassuntiva parametri da impostare su scheda di caldaia LUNA HT NUVOLA HT LISTA PARAMETRI 1.120 1.240 1.280 280 330 330 Par. Descrizione Parametri 12kW 24kW 28kW 24/28 kW 28/33 kW 28/33 kW 507 Temperatura massima (°C) di mandata in riscaldamento (impianto a bassa temperatura). 25÷45 514 Incremento temperatura (°C) di mandata caldaia rispetto alla temperatura del circuito a bassa temperatura. 5 533 Pendenza curva riscaldamento circuito (impianto a bassa temperatura) 15 552 Settaggio sistema idraulico 51 54 51 596 Tempo (s) di apertura della valvola 3 vie circuito riscaldamento a bassa temperatura. 180 615 Funzione programmabile uscita 0 Nota : i parametri che non riguardano il circuito a bassa temperatura sono riportati nel manuale istruzioni della caldaia
Страница 15 PDF
Страница 16
Pag. 16/32 13. Caratteristiche tecniche Tensione di alimentazione AC 230 V Frequenza nominale 50 Hz Potenza assorbita : Sistema standard con n°1 pompa alta temperatura+1 pompa bassa temperatura 200 W Sistema opzionale con n°2 pompe alta temperatura+1 pompa bassa temperatura 290 W Grado di protezione IPX5D secondo EN 60529 Dimensioni 600x450x160 (mm) Peso Sistema standard senza kit (pompa zona alta temperatura + pompa zona bassa temperatura) 17,3 Kg Sistema con kit opzionale (aggiunta 2a pompa zona alta temperatura) 22,5 Kg
Страница 16 PDF
Страница 17
Pag. 17/32 1. Description of the controller and its water circuits This open collector controller allows you to control a two-circuit installation comprising one high temperature circuit (≤ 85°C) and one low temperature circuit (≤ 45°C). The unit’s compact size (only 160 mm deep) facilitates flush fitting in a recess as well as normal wall hanging. The controller incorporates a pump for the high temperature circuit controlled by a thermostat in the heated area. The low temperature circuit comprises a mixer valve and a pump. This pump can be controlled by a room thermostat, a room unit SIEMENS QAA73 or through a climatic control using an external probe sensor. The controller has all the necessary provisions for a second pump (for the high temperature circuit) controlled by a thermostat in the heated area. 2. Dimensions and hydraulic connections Figura 1 Figure 2 GB Legend: M G3/4” F : boiler delivery line R G3/4”M : boiler return line Mat G3/4” F: high temperature (HT) delivery line≤ 85°C Rat G3/4”F: high temperature (HT) return line Mbt G1” M: low temperature (LT) delivery line ≤ 45°C Rbt G1” F: low temperature (LT) return line Figure 1
Страница 17 PDF
Страница 18
Pag. 18/32 3. Assembly of AGU 2.500 accessory in the boiler’s control panel After removing the control box cover, assemble the bearing (B) supplied with the accessory, then assemble the same accessory (C). Note: To facilitate the connection between the accessory and the pcb, connect wiring (A) to the pcb before fixing bearing (B). To assemble the control box cover cut the two little pegs. The AGU 2.500 accessory is supplied with this controller. Figure 3
Страница 18 PDF
Страница 19
Pag. 19/32 4. Accessory AGU 2.500 electric wiring diagram Electrical connection with AGU 2.500 AGU 2.500 connectors Electronic board connectors Description 1-2 X 51 1-2 X 101 NTC probe 1(L)2(N) X 52 1(L)2(N) X 203 Power supply 230V ∼ AGU 2.500 3(L)4(N) X 52 1(L)2(N) X 201 Low temperature circuit pump power supply 230V ∼ 5(close)6(N)7(open) X 52 5(L)4(N)3(L) X 201 Mix valve command: open - close Electrical connection terminal board M2 M2 terminal board Morsetti scheda elettronica Description 3-4 1-2 X 11 Boiler room thermostat RT (TA-figure 4) Hot water request to boiler. 5-6 3-4 X 101 Boiler safety thermostat ST (TP-figure 4) Figure 4 Electronic controller board for twin circuit installations SIEMENS PCB model LMU 54. (connector X-40) SIEMENS PCB terminal board (M2) open close
Страница 19 PDF
Страница 20
Pag. 20/32 5. Controller electric wiring diagram Connect the controller to a 230 V single phase + earth mains power supply using the three-core cable provided. Fit the electrical mains connection with a two-pole switch with a contact gap of at least 3 mm. If you need to replace the mains power cable, use only a HAR H05 standard 3x0.75 mm2 cable with maximum sheath diameter of 8 mm. IMPORTANT! To switch off all electrical power to the controller, press the button on the front panel (power indicator off; see figure 5). Figure 5 Tasto ON/OFF
Страница 20 PDF
Страница 21
Pag. 21/32 Electrical connection connectors X1 Mains power 230 V (2 L; 1 N). FA1 Mains earth. X3 Pump power. 1 Live, low temperature pump. 2 Neutral, low temperature pump. 3 Live, high temperature pump. 4 Neutral, high temperature pump. 5 (N) -6 (L) Provision for the optional second high temperature pump. X3B Mixer valve power. 1 Live, valve opening. 2 Neutral. 3 Live, valve closing. 4 Not used. X4 NTC sensor input. 1-2 NTC sensor, mixed circuit. 3-4 Not used 5-6 Safety thermostat 50°C (clicson). X7 Room temperature Thermostats (RT) 1-2 Provision for High Temperature Room Thermostat, 2nd High Temperature area (RT3). 3-4 Room Thermostat, High Temperature area (RT2). 5-6 Not used Figure 6 ON/OFF button RT 3 WIRE COLOURS: B White R Red BL Blue G/V yellow/green C Light blue M Brown N Black RT 2
Страница 21 PDF
Страница 22
Pag. 22/32 6. Descriptions of electronic control card Leds Figure 7 LED On: valve opening LED On: valve closing LED On: Live 230 V~ LED On: pump 2 switch on (RT3 – fig.6) LED On: pump 1 switch on (RT2 – fig.6)
Страница 22 PDF
Страница 23
Pag. 23/32 7. Setting the PCB parameters 1 - press both the following two ▲▼ buttons on the boiler’s front panel together, until the parameter “H90” appears on the display; 2 - press the ▲ key, to select the parameter in increasing order, press the ▼ button to select the parameters in decreasing order. Press the +/- keys to modify the parameters, which appear on the display. The chosen parameters are automatic saved when a new parameter is selected 3 – press the button to save and to exit the installer level; For the description of the parameters, please consider “Setting parameters on main boiler PCB” (paragraph 12). 8. Management of different zones 8.1 WITH EXTERNAL PROBE SENSOR Connect the external probe sensor to terminal boiler board M2 pins 7-8 (figure 4), as described in the instructions booklet. 8.1.1 Climatic regulation (without RT and QAA73) Ensure that there is the jumper between connections 1-2 and 3-4 of terminal boiler board M2 (figure 4). 8.1.2 Use of room temperature thermostats (RT) high temperature zone: - The contact of the room temperature thermostat of the high temperature circuit must be connected to connector X7 pins 3-4 (RT2), of the electronic board controller (figure 6). - The daily program must be set directly on the boiler control panel. - The choice of the temperature curve “kt”, relating to the part of the circuit with high temperature, must be selected by setting parameter 532. See graph 1 of the instruction’s manual for selecting the curve referred to a room temperature of 20°C. - The chosen curve can be shifted by pressing the button on the boiler control panel, and modify the value displayed by pressing the + and - . Increase the value displayed, if the room temperature required is not reached inside the room, which should be heated.
Страница 23 PDF
Страница 24
Pag. 24/32 Low temperature zone: - The contact of the room temperature thermostat must be connected to the terminal boiler board M2 pins 1-2 (figure 8). - The choice of the maximum heating temperature must be selected by setting parameter 507. - The parameter 615 must be “0”. - The parameter 552 must be “51” for heating-only boilers, or equipped with d.h.w. tank, and “54” for combi-boilers. - The choice of the temperature curve “kt” must be selected by setting parameter 533. See graph 1 of the instruction’s manual for selecting the curve referred to a room temperature of 20°C. - The chosen curve can be shifted by setting the parameter 535. 8.1.3 Use of room thermostat and QAA73 temperature control device high temperature zone: see section 8.1.2 low temperature zone - The temperature control device QAA73 must be connected to the terminal boiler board M2 pins 1-2 (figure 9). - The choice of the maximum heating temperature must be selected by setting parameter H507. - The parameter H615 must be “0”. - The parameter 552 must be “51” for heating-only boilers, or equipped with d.h.w. tank, and “54” for combi-boilers. IMPORTANT: The parameter 80 “HC2 gradient”, which can be set on the QAA73 temperature control device, must be set as --.- not active (see section 15.2 of the Installer’s and User’s boiler manual). - The choice of the temperature curve “kt” must be selected by setting parameter 70 “HC2 gradient”, of the temperature control device QAA73, as shown in the section 15.2 of the Installer’s and User’s manual. See graph 3 for selecting the curve referred to a room temperature of 20°C. - The curve is shifted automatically on the basis of the room temperature set using the QAA73 climate control.
Страница 24 PDF
Страница 25
Pag. 25/32 8.2 WITHOUT EXTERNAL PROBE SENSOR 8.2.1 Use of room temperature thermostats (RT) high temperature zone: - The contact of the room temperature thermostat of the high temperature circuit must be connected to connector X7 pins 3-4 (RT2) of the electronic board controller (figure 6). - The choice of the room temperature and the daily program, must be set directly on the boiler control panel. low temperature zone: - The contact of the room thermostat must be connected to the terminal boiler board pins 1-2 (figure 8). - The choice of the maximum heating temperature must be selected by setting parameter H507. - The parameter H615 must be “0”. - The parameter 552 must be “51” for heating-only boilers, or equipped with d.h.w. tank, and “54” for combi-boilers. 8.2.2 Use of room thermostat and QAA73 high temperature zone: see section 8.2.1 low temperature zone: - The QAA73 must be connected to the terminal boiler board M2 pins 1-2 (figure 9). - The choice of the maximum heating temperature must be selected by setting parameter 507. IMPORTANT: The parameter 80 “HC2 gradient”, which can be set on the QAA73, must be set as --.- not active (see section 15.2 of the Installer’s and User’s manual).
Страница 25 PDF
Страница 26
Pag. 26/32 Room thermostat (RT ) and room unit QAA73 electric wiring diagrams on boiler board terminal M2 Figure 9 Figure 8 Room thermostat (Low temperature zone) QAA73 (Low temperature zone) RT M2 M2
Страница 26 PDF
Страница 27
Pag. 27/32 9. Floor thermostat connecting (low temperature floor circuit) The controller is provided with a safety temperature thermostat of 50°C for a low temperature circuits. If it’s necessary to use a different temperature thermostat, it is possible to use a collar thermostat, available on the market, which must be connected to the terminal boiler board M2 pins 5-6 (figure 4). 10. Pump head values 10.1. Low temperature circuit pump 0 1 2 3 4 5 6 7 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 Water flow l/h Head mH2O 10.2. High temperature circuit pump 0 1 2 3 4 5 6 7 8 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 Water flow l/h Head mH2O Graph 1 Graph 2 III II III II
Страница 27 PDF
Страница 28
Pag. 28/32 11. Optional second pump kit for the high temperature circuit The controller has all the necessary provisions for a second pump for the high temperature circuit. The second pump kit comprises: - 1 x Grundfoss UPS 15/60 230 V-50 Hz pump - 3 x pipes (A, B, C in figure 10) - 1 x non-return valve, G ¾ FF (figure 10); - 1 x electrical wiring loom. The second pump must be connected to terminal X3 pins 5-6 (figure 6). The room temperature thermostat of this circuit must be connected to terminal X7 pins 1-2 (RT3 figure 6) B Figure 10 UPS 15/60 PUMP Non-return valve, G ¾ FF A C
Страница 28 PDF
Страница 29
Pag. 29/32 12. Setting parameters on main boiler PCB LUNA HT NUVOLA HT PARAMETER LIST 1.120 1.240 1.280 280 330 330 Par. Descrizione Parametri 12kW 24kW 28kW 24/28 kW 28/33 kW 28/33 kW 507 Maximum flow setpoint temperature (°C) (low temperature circuit) 25÷45 514 Boiler temperature (°C) setpoint boost with mixing circuit 5 533 Heating curve slope heating circuit (low temperature circuit) 15 552 Hydraulic system adjustment 51 54 51 596 Mix valve closing time (s) (low temperature circuit) 180 615 Function programmable output 0 Note: The parameters, which are not referred to a low temperature heating circuit, are reported in the boiler Installer’s and User’s manual
Страница 29 PDF
Страница 30
Pag. 30/32 13. Technical specifications Mains voltage AC 230 V Nominal frequency 50 Hz Consumption : Standard system with 1 high temperature pump +1 low temperature 200 W Optional system with 2 high temperature pumps +1 low temperature 290 W Protection rating IPX5D to EN 60529 Dimensions (mm) 600x450x160 Weight Standard system without optional kit (high temperaure zone + low temperature zone) 17,3 Kg System with optional kit (standard system + 2ndhigh temperaure zone) 22,5 Kg
Страница 30 PDF
Страница 31
Pag. 31/32
Страница 31 PDF
Страница 32
Pag. 32/32 L’azienda, nella costante azione di miglioramento dei prodotti, si riserva la possibilità di modificare i dati espressi in questa documentazione in qualsiasi momento e senza preavviso. La presente documentazione è un supporto informativo e non considerabile come contratto nei confronti di terzi. The manufacturer operates a policy of continuous improvement for all its products and therefore reserves the right to modify the product described herein and its specifications at any time without prior notice. This instruction manual is written as a support for installation only and is not contractually binding in any way. Ediz.4-12/03 Codice / Code 923.196.3 IT GB
Страница 32 PDF